From yahoo Sent Thu, Nov 24th 2016, 14:51
It is mentioned on the A-190-3 info page: www.doepfer.com > English > PRODUCTS > A-100 > Module Overview > A-190-3 The info page says: "In the A-190-2 the LED shows the gate function (i.e. LED = on while gate = high / LED = off while gate = low). In the A-190-3 the LED is permanently on and turns off only for a short time when an incoming Midi message is recognized." Best wishes Dieter Doepfer > -----Ursprüngliche Nachricht----- > Von: xxxxxxx_xxxx@xxxxxxxxxxx.xxx [mailto:xxxxxxx_xxxx@xxxxxxxxxxx.xxx] > Gesendet: Donnerstag, 24. November 2016 15:15 > An: Doepfer a100 > Betreff: Re: AW: [Doepfer_a100] A-190-3 + A190-4 and A-143-1 > > > Thanks, I seize the opportunity to ask whether it's normal or not > that on the A-190-3 the gate led is on. Powering on, it blinks > several times than it stays on, anyway, even without any > connection (USB, MIDI). > > > ----- Mail original ----- > De: "xxxxx@xxxxxxx.xx [Doepfer_a100]" <xxxxxxx_xxxx@xxxxxxxxxxx.xxx> > À: "Doepfer a100" <xxxxxxx_xxxx@xxxxxxxxxxx.xxx> > Envoyé: Jeudi 24 Novembre 2016 12:34:44 > Objet: AW: [Doepfer_a100] A-190-3 + A190-4 and A-143-1 > > You find a detailed explanation of the CV/Gate bus principles on our > website: > > www.doepfer.com > PRODUCTS > A-100 > Technical details > Power Supply and > System Bus > > The A-143-1 does not pick up the gate signal from the bus. > > Best wishes > Dieter Doepfer > > > > Hello, > > > > I purchased an A-190-3 and getting confused a bit for the cv/gate > > bus jumpers option, as I already own a A-190-4. > > > > Will I have to care of keeping/removing the concerned jumpers > > even though the two interfaces will be mounted on different rows > > within the A-100P9 case? > > > > And does the A-143-1 receive gates from the bus if the A-190-3 > > jumpers are left mounted as coming from the retailer? > > > > Moreover, Doepfer web page doesn't mention the A-190-4, but since > > it is descending from A-190-1 I think it might be concerned: > > Important notes: > > The module comes with installed bus jumpers for CV and Gate. One > > has to remove the jumpers if e.g. an A-164, A-190-1, A-190-2, > > A-185-1 or A-185-2 is already connected to the CV and/or gate > > lines of the same bus board! > > > > Best, Diego > > > > ------------------------------------ > > ------------------------------------ > > > ------------------------------------ > > Yahoo Groups Links > > > > > > ------------------------------------ > Posted by: xxxxxxx@xxxx.xx > ------------------------------------ > > > ------------------------------------ > > Yahoo Groups Links > > > ------------------------------------ ------------------------------------ ------------------------------------ Yahoo Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Doepfer_a100/ <*> Your email settings: Individual Email | Traditional <*> To change settings online go to: http://groups.yahoo.com/group/Doepfer_a100/join (Yahoo! ID required) <*> To change settings via email: xxxxxxx_xxxx-xxxxxx@xxxxxxxxxxx.xxx xxxxxxx_xxxx-xxxxxxxxxxxx@xxxxxxxxxxx.xxx <*> To unsubscribe from this group, send an email to: xxxxxxx_xxxx-xxxxxxxxxxx@xxxxxxxxxxx.xxx <*> Your use of Yahoo Groups is subject to: https://info.yahoo.com/legal/us/yahoo/utos/terms/