From Diego Ragnini diegora Sent Mon, Nov 14th 2016, 12:56
oh yes, I did believe the ribbon being 500 mm, unfortunately the largest in= tellijel case is 537.3 mm, so I might opt to build a handle wooden top for the A-100LC3 to make the ca= se portable, wider enough for hosting the ribbon and containing left and ri= ght small cases for the 2 PSU's. After transport the ribbon can be layered = on the top of the case or anywhere else. The only issue would be for hand l= uggage on planes, typically asking to stay within 55cm length. I thank you a lot for support Best regards Il giorno 14/nov/2016, alle ore 11:10, xxxxx@xxxxxxx.xx [Doepfer_a100] <Doe= xxxx_xxxx@xxxxxxxxxxx.xxx> ha scritto: > Then it should be no problem. Simply mount the R2M manual to a 1U blind > panel by means of the four M3 threads at the bottom of the R2M manual > housing. The lenght of the R2M manual is ~ 600 mm (plus the USB connector= ). > If the width of the case is more it should work. I'd recommend to keep th= e > housing as it guarantees the mechanical stability required for the pressu= re > and position sensors. >=20 > Best wishes > Dieter Doepfer >=20 >=20 >> -----Urspr=FCngliche Nachricht----- >> Von: Doexxxx_xxxx@xxxxxxxxxxx.xxx [mailto:Doexxxx_xxxx@xxxxxxxxxxx.xxx] >> Gesendet: Montag, 14. November 2016 10:58 >> An: Doexxxx_xxxx@xxxxxxxxxxx.xxx >> Betreff: Re: [Doepfer_a100] R2M Manual Ribbon controller - 1U row >> installation >>=20 >>=20 >>=20 >>=20 >> Thanks, though I imagined a row longer than 84hp, there's some on >> sale of 90HP, 104HP, 1 row @ 3U + 1 row @ 1U. I do believe that >> Intellijel makes it. Of course, then it would require some work >> to manufacture a panel to host the Manual. >>=20 >>=20 >> Best regards, Diego >>=20 >>=20 >>=20 >> Il giorno 14/nov/2016, alle ore 10:45, xxxxx@xxxxxxx.xx >> [Doepfer_a100] <Doexxxx_xxxx@xxxxxxxxxxx.xxx> ha scritto: >>=20 >>=20 >>=20 >> I'm sorry, this will not work because the position sensor is longer than >> 19". The active area of the position sensor is 500 mm plus the >> area required >> for the connector (~ 70mm). That's more than 19" which is about >> 483 mm. It's >> not possible to shorten the positions sensor without damaging the >> sensor (in >> contrast to the pressure sensor which can be easily shortened). >>=20 >> Best wishes >> Dieter Doepfer >>=20 >>> Hello, >>>=20 >>> is there anybody who tried to ease installation of the manual >>> onto a 1U eurorack row ? >>>=20 >>> Thanks >>=20 >>=20 >>=20 >>=20 >>=20 >>=20 >>=20 >>=20 >=20 >=20 >=20 > ------------------------------------ >=20 > ------------------------------------ >=20 >=20 > ------------------------------------ >=20 > Yahoo Groups Links >=20 >=20 >=20 ------------------------------------ ------------------------------------ ------------------------------------ Yahoo Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Doepfer_a100/ <*> Your email settings: Individual Email | Traditional <*> To change settings online go to: http://groups.yahoo.com/group/Doepfer_a100/join (Yahoo! ID required) <*> To change settings via email: xxxxxxx_xxxx-xxxxxx@xxxxxxxxxxx.xxx=20 xxxxxxx_xxxx-xxxxxxxxxxxx@xxxxxxxxxxx.xxx <*> To unsubscribe from this group, send an email to: xxxxxxx_xxxx-xxxxxxxxxxx@xxxxxxxxxxx.xxx <*> Your use of Yahoo Groups is subject to: https://info.yahoo.com/legal/us/yahoo/utos/terms/