From yahoo Sent Mon, Jul 3rd 2017, 11:24
I do not recommend to use one transformer for two units. Each A-100LC3 should have it's own transformer. As the transformer has 2.4A available the max. current would be 600 mA only (= 2400/4). And if the wiring of the second connector is wrong you generate a short circuit and will damage the transformer and possible the supplies and installed modules. Best wishes Dieter Doepfer > -----Ursprüngliche Nachricht----- > Von: xxxxxxx_xxxx@xxxxxxxxxxx.xxx [mailto:xxxxxxx_xxxx@xxxxxxxxxxx.xxx] > Gesendet: Montag, 3. Juli 2017 10:17 > An: xxxxxxx_xxxx@xxxxxxxxxxx.xxx > Betreff: Re: [Doepfer_a100] Re: A-100 LC3 PSU (?) > > > Hi Dieter thanks a lot for this specification > > Otherwise, could I use the original 2.4A Doepfer transformer > (which belongs to a case I already own) to operate the TWO kits > simultaneously? (Assuming that an adapter to double the plug > could be found ) > > Best, Diego > > > Il giorno 03 lug 2017, alle ore 10:03, xxxxx@xxxxxxx.xx > [Doepfer_a100] <xxxxxxx_xxxx@xxxxxxxxxxx.xxx> ha scritto: > > > > You may use this power supply. But the max. output current is then only > > 500mA. Please refer to the information on our website: > > > > www.doepfer.com > English > PRODUCTS > A-100 > DIY case kit: > > > > "to operate the kit an external transformer with 14-16V/2.4A AC > is required, > > the current of the transformer has to be twice the value of the > +/-12V DC > > current, the max. value is 2.4A (corresponding to 1200mA for +/-12V DC), > > even smaller current output is possible; the current output of the power > > supply is half the current of the external transformer as the > currents for > > both voltages +/-12V are required (if e.g. the transformer outputs max. > > 1000mA the max. power supply current is 500mA for +/-12V)" > > > > Best wishes > > Dieter Doepfer > > > > > >> -----Ursprüngliche Nachricht----- > >> Von: xxxxxxx_xxxx@xxxxxxxxxxx.xxx [mailto:xxxxxxx_xxxx@xxxxxxxxxxx.xxx] > >> Gesendet: Freitag, 23. Juni 2017 15:22 > >> An: xxxxxxx_xxxx@xxxxxxxxxxx.xxx > >> Betreff: [Doepfer_a100] Re: A-100 LC3 PSU (?) > >> > >> > >> > >> > >> > >> Sorry I was wrong in the description of the problem, forget it. > >> > >> > >> My worry here concerns the fact that a (not original) 1000mA > >> transformer is used for a (supposed) 1200mA power supply. I say > >> supposed because I dont know whether this case came with a > >> lower supply mA value than todays model (the original Doepfer > >> transformer installed today delivers 2400mA). > >> > >> > >> So, the PSU and the board are original Doepfer, the external > >> transformer is not. > >> > >> > >> Do you think this might cause issues to the power supply, the > >> board or the modules? > >> > >> > >> The link describes the not original transformer.. > >> > >> > >> http://www.velleman.eu/products/view/?country=fr&lang=en&id=365838 > >> > >> > >> Since I already own this case with 1200mA and the original ext. > >> transformer (2400mA), would be technically possible to use this > >> original transformer for both cases at the same time? > >> > >> > >> Best, > >> dxx > >> > >> > >> > >> > >> > >> > >> Il giorno 18 giu 2017, alle ore 22:47, Diego Ragnini > >> <xxxxxxx@xxxx.xx> ha scritto: > >> > >> > >> Hi everybody > >> > >> > >> A guy sells a second hand 2,5 years old A-100 LC3 of 1000mA, with > >> a PSU which is not the original one. Apparently it had few issues > >> and decided to replace it for not clearly specified reasons. He > >> forwarded me the link for this PSU > >> > >> > >> http://www.velleman.eu/products/view/?country=fr&lang=en&id=365838 > >> > >> > >> I would be glad if someone could confirm the compatibility with > >> the Doepfer system. He states that everything works flawlessly > >> with it. I am surprised to know about issues on the original > >> transformer for this unit, which I own in the new version > >> (1200mA) and cannot find anything to complain about its PSU, > >> absolutely sturdy and reliable. > >> > >> > >> Best regards, > >> Diego > >> > >> > >> > >> > >> > > > > > > > > ------------------------------------ > > > > ------------------------------------ > > > > > > ------------------------------------ > > > > Yahoo Groups Links > > > > > > > > > > ------------------------------------ > Posted by: Diego Ragnini <xxxxxxx@xxxx.xx> > ------------------------------------ > > > ------------------------------------ > > Yahoo Groups Links > > > ------------------------------------ ------------------------------------ ------------------------------------ Yahoo Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Doepfer_a100/ <*> Your email settings: Individual Email | Traditional <*> To change settings online go to: http://groups.yahoo.com/group/Doepfer_a100/join (Yahoo! ID required) <*> To change settings via email: xxxxxxx_xxxx-xxxxxx@xxxxxxxxxxx.xxx xxxxxxx_xxxx-xxxxxxxxxxxx@xxxxxxxxxxx.xxx <*> To unsubscribe from this group, send an email to: xxxxxxx_xxxx-xxxxxxxxxxx@xxxxxxxxxxx.xxx <*> Your use of Yahoo Groups is subject to: https://info.yahoo.com/legal/us/yahoo/utos/terms/